Happymodel Mobula6 2024 V3 ELRS 1S Whoop - A30
*May differ from pictures shown.
The Happymodel Mobula6 2024 V3 1S 65mm Ultra Light Micro FPV Whoop comes equipped with a lightweight AIO flight controller and Serial ELRS receiver, as well as a 5.8G OpenVTX for optimal performance. With super light brushless motors, specifically SE0702 weighing only 1.46 grams, this product offers smooth and powerful flight capabilities. The New 1200TVL Nano5 camera captures awesome footage, making it perfect for those looking for a professional and informative FPV experience. Compatible with both 1S lipo and LIHV batteries.
Flight controller connection diagram:
Compatible Batteries
Features:
Come with New CrazyG473 AIO flight controller
Happymodel New 1200TVL Nano5 camera
Super light 1S 65mm Brushless whoop only 17.6g
Equipment with the lightest brushless motors-SE0702 only 1.46gram
Smooth and powerful
Built-in Serial ELRS receiver
Built-in Power max to 400mw openVTX
Specifications:
Brand Name: Happymodel
Item Name: Mobula6 2024 V3 1S 65mm ultra light micro FPV Whoop
Wheelbase: 65mm
Size: 81mm*81mm*37mm
Weight: 17.6g
Receiver option:
2.4GHz ExpressLRS Serial receiver
| Mobula6 2024 V3 | Mobula6 2024 V2 | |
| Flight controller | CrazybeeG473 | SuperX ELRS V2.0 |
| Firmware target | Betaflight 4.6 CrazybeeG473 | Customized STM32F411 |
| Built-in ExpressLRS receiver | Serial ELRS 2.4GHz | Serial ELRS 2.4GHz |
| Built-in Dshot ESC | 5A | 5A |
| Receiver antenna plug | Enameled Copper wire | Enameled Copper wire |
| Onboard VTX power | 25mw~400mw | 25mw~400mw |
| Brushless Motor | 0702 KV28000 no plug | 0702 KV28000 with plug |
| Propeller | Gemfan 1208-3 tri-blade | Gemfan 1208-3 tri-blade |
| Battery plug | A30(compatible with BT2.0) | A30(compatible with BT2.0) |
| Frame | Mobula6 2024 frame 2.76gram | Mobula6 2024 frame 2.76gram |
SPECIFICATIONS
- Brand Name: Happymodel
- Item Name: Mobula6 2024 1S 65mm ultra light micro FPV Whoop
- Wheelbase: 65mm
- Size: 81mm*81mm*37mm
- Weight: 17.7g
Motor
- Mode: SE0702 KV28000 no plug version
- Configuration: 9N12P
- Stator Diamter: 7mm
- Stator Length: 2mm
- Shaft Diameter: Φ1mm
- Motor Dimension(Dia.*Len): Φ9.5mm*14mm
- Weight(g): 1.46g
- No.of Cells(Lipo): 1S only
Propellers
- Materials: PC
- Inch: 31mm
- Pitch: 0.8 in
- Weight: 0.21g
- Mount hole diameter: 1mm
Flight controller
- MCU: STM32G473CEU6
- Gyro: ICM42688P
- Sensor: Voltage & Current
- BEC: 5V, Max. 2A
- UART: UART 1, UART 2, UART 3 (For RX), UART 4(For VTX)
- BetaFlight OSD: AT7456E
- ESC: 5A continuous
- RX: Serial ELRS 2.4GHz
- RX antenna: Enameled copper wire 31mm length
- Receiver firmware target: HappyModel EP1/EP2 2.4GHz RX
- OPENVTX: 5.8GHz 48 channels, Max. 400mW
- FC firmware target: CRAZYBEEG473
- USB port: SH1.0-4Pin
- Battery connector: A30
- Mounting hole size: 25.5mm x 25.5mm
- Weight: 3.83g without pigtail and vtx antenna
Onboard 4in1 ESC
- Power supply: 1S LiPo/LiPo HV
- Current: 5A continuous peak 6A (3 seconds)
- Support BLHeliSuite programmable
- Factory firmware: Bluejay v0.21
- Firmware target: A_X_5_96KHz
- Default protocol: DSHOT300 DSHOT600
- Recommend ESC Startup power value to min1100/max1200
Onboard Serial ExpressLRS receiver
- Packet Rate option: 50Hz/150Hz/250Hz/500Hz
- ExpressLRS Firmware version: V3.0
- RF Frequency: 2.4GHz
- Antenna : Enameled copper wire antenna
- Telemetry output Power: <12dBm
- Receiver protocol: Serial_based CRSF
- Compatible with ExpressLRS V3.x.x TX Module
- Could flash single ELRS receiver firmware by Wifi
- ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx
Onboard 5.8g VTX
- OPENVTX Firmware
- Support firmware upgrade by openvtx configurator
- Output power: PIT/10/25/100/400
- Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz
- Channel SEL: SmartAudio2.1
- Modulation type: FM
- Operating temperature: -10℃~+80℃
- Antenna port: IPEX1/U.FL
Nano5 Camera
- Image Sensor: 1/3″ CMOS
- Horizontal Resolution: 1200 TVL
- Lens: 2.1mm (M10) 155° FOV
- TV System: NTSC
- Signal-to-Noise Ratio: >52dB
- Electronic Shutter: Auto
- Automatic Gain Control (AGC): Auto
- Minimum Illumination: 0.001Lux@1.2F
- Digital Wide Dynamic Range: Auto
- Power Supply: DC 3-5.5V
- Current: 110mA@5V 120mA@3.3V
- House Material: ABS
- Net Weight: 1.57g (1.0mm plug version)
PACKAGE Contents
- 1x Mobula6 2024 1S 65mm whoop Drone Frame + Canopy
- 1x CrazybeeG473 AIO 5-IN-1 Flight controller
- 4x SE0702 KV28000 brushless motor
- 1x HQPROP ultralight whoop prop 1.2×1.1×3(2cw+2ccw)
- 1x Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw)
- 1x Nano5 1200TVL camera NTSC 4:3
- 1x Onboard 5.8G 25mw~400mw VTX
- 1x Spare canopy
- 1x Propeller disassemble tool
- 1x Screw driver
- Receiver Type:
- ExpressLRS
