HappyModel 1S Moblite7 Avatar Whoop V3 - ELRS
*May differ from pictures shown.
Lightweight 75mm whoop using the Walksnail 1S VTX and nano camera compatible with the FatShark Dominator HD / Walksnail Avatar goggles.
Specifications
- Brand Name: Happymodel
- Model: Moblite7 Walksnail V3
- Frame wheelbase: 75mm
- Weight: 34.5 gram without battery
- Size: 98mm*98mm*48mm
- Receiver option: UART ELRS V3.0 2.4GHz
- Compatible with 1S Lipo battery or Lihv battery
- Battery Plug: GNB A30 (compatible with BT2.0)
Flight controller
SuperX HD ELRS
- Betaflight 4.4.2 firmware ready
- Firmware target: CRAZYBEEF4DX
- MCU:STM32F411CEU6 (100MHz, 512K FLASH)
- Sensor: BMI270 or ICM42688P (SPI connection)
- Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone
- Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read
- Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update
- Bluejay ESC Firmware ready
- Built-in 5V 1A BEC
- Built-in voltage detection
- No Betaflight analog osd chip
Onboard 4in1 ESC
- Power supply: 1-2S LiPo/LiPo HV
- Current: 12A continuous peak 15A (3 seconds)
- Support ESC-Configurator and BLHELI_S Suite configurator
- Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz
- Default protocol: DSHOT300
Onboard UART ExpressLRS 2.4GHz Receiver
- RF Frequency: 2.4GHz
- Antenna: enameled copper wire 31mm length
- Telemetry output Power: <12dBm
- Receiver protocol: CRSF
- Default firmware version: ExpressLRS V3.0.1
- The same hardware with Happymodel EP1 receiver
- Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through
Motor
- Model: 1002 20000KV
- Configu-ration:9N12P
- Stator Diameter:10mm
- Stator Length:2mm
- Shaft Diameter:Φ1.5mm
- Motor Dimension(Dia.*Len):Φ13.5mm*12.5mm
- Weight(g):2.5g
- No.of Cells(Lipo):1S only
Propeller
- Gemfan 1610-2 Bi-blades Weight:0.24g
- Material: PC
- Pitch:1 inch
- Props Dia:40mm
- Center Hole Dia:1.5mm
VTX
- Model: Avatar mini 1s module
- Communication Frequency: 5.725-5.850 GHz
- Transmitter Power(EIRP): FCC:<25.5dBm; CE:<14dBm; SRRC: <20dBm;MIC:<25dBm
- l/o Interface: JST1.O*6(Power in)JST1.O*4(USB)
- Mounting Holes: 25.5*25.5 mm
- Dimensions: 33*33*6.5 mm
- Storage: 8G
- Recording: 1080p/720p
- Weight: 6.8 g
- Operating Temperature: -20-40℃
- Channels: 8
- Wide Power lnput: 3.1V-5V
- Supported FC System: Betaflight
- OSD: Canvas mode
- Bitrate: 25mbps / 50mbps
- Latency: Average delay 22ms
- Antenna connector: IPEX
Camera
- Model: Avatar nano
- lmage Sensor: 1/2.7”Inch
- Resolution: 1080P/6Ofps,720P/120fps,72OP/6Ofps
- Ratio: 16/9 4/3
- Lens: 2.1mm
- FOV 170°
- Aperture: F2.0
- Shutter: Rolling shutter
- Min.Illumination: 0.001Lux
- Weight: 3.5g
- Dimensions: 14*14*17mm
- Coaxial Cable: 45mm
Package Contents
- 1 x Mobula7 v4 75mm frame +Canopy
- 1 x SuperX HD ELRS AIO flight controller
- 1 x Happymodel 1002 KV20000 Unibell brushless motor
- 1 x Gemfan 1610-2 bi-blades propeller(4cw+4ccw)
- 1 x Walksnail Avatar nano HD camera
- 1 x Walksnail Avatar mini 1s tx module
- 1 x Spare Canopy
- 1 x Propeller disassemble tool
- 1 x Screw driver
