HappyModel 1-2S Mobula8 Whoop - ELRS UART
*May differ from pictures shown. Are you tired of the power performance of the 1S whoop you own? Do you want more power to ripping and roaring in your backyard? Yes, here comes Mobula8, which is Happymodel’s first attempt on 85mm frame. It comes with X12 series flight controller, EX1103 KV11000 motor and Gemfan Hurricane 2023 tri-blade propeller, which has excellent power performance and extremely smooth flight.
VIDEO
FEATURES
X12 Pro 5-IN-1 AIO flight controller built-in 2.4G ELRS V3.0 via UART and OPENVTX VTX Power up to 400mw EX1103 KV110000 motors CaddxFPV Ant FPV camera Smooth and powerful Compatible for 1S-2S Lipo/LIHV battery 3D Printed Camera Lens Protector
SPECIFICATIONS
Motors
Mode: EX1103 KV11000 Configuration: 9N12P Stator Diameter: 11mm Stator Length: 3mm Shaft Diameter: Φ1.5mm Motor Dimension(Dia.*Len): Φ13.5mm*15.5mm Weight(g): 3.8g No. of Cells(Lipo): 1-2S
Propellers
Weight: 0.88g Material: PC Pitch: 2.3inch Props Diameter: 52.17mm Center Thickness: 5mm Center Hole Diameter: 1.5mm
Flight controller
X12 ELRS Pro v1.1 AIO 5-IN-1 Flight controller
MCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4
Sensor: ICM42688P(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw (MSP control)
Built-in UART ExpressLRS v3.0.0
Built-in voltage meter sensor , voltage meter scale 110
Built-in current meter sensor , current meter scale 470
Onboard 4in1 ESC
Power supply: 1-2S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Firmware target: Z_H_30
Default protocol: DSHOT300
Support Bluejay firmware
Onboard UART ExpressLRS 2.4GHz Receiver
Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V3.0
RF Frequency: 2.4GHz
Antenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: Serial_based CRSF
Compatible with ExpressLRS V3.x.x TX Module
Could flash single ELRS receiver firmware by Wifi
ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx
Onboard 5.8g OPENVTX
Firmware version: OPENVTX
SmartAudio v2.1
PIT Mode support
RCE Mode support
Channels: 37ch
Transmitting Power: 0/RCE/25mw/100mw/400mw
Power supply: DC 5V
Current (5v): <650ma (400mw)
Caddx ANT 1200TVL Camera
Image Sensor: 1/3″ CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC or PAL
IMAGE: 16:9 or 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio : >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm
Min. Illumination: 0.001Lux@F1.2
Auto Gain Control: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V
Weight: 2g (N.W.)
PACKAGE Contents
1 x Happymodel Mobula8 1-2S 85mm Analog Micro FPV Whoop Drone 1 x Gemfan Hurricane 2023 tri-blade propellers (4CW+4CCW) 1 x Screw Driver 1 x Extra camera canopy
