HappyModel Mobula8 V3 (ELRS)
*May differ from pictures shown.
ELRS via UART! :)
The new Mobula8 UART ELRS V3 brings serious upgrades to Happymodel’s 85mm whoop. It now features the X14 5-in-1 AIO flight controller with built-in UART ELRS 2.4 GHz, OPENVTX up to 400mW, and easy Wi-Fi firmware flashing. Paired with EX1103 11000KV motors and Gemfan 2023 props, it delivers smooth, powerful 2S performance in a compact 85 mm frame. Light, agile, and far more capable than the original—perfect for backyard ripping.
FEATURES
- X14 ELRS 5-IN-1 AIO flight controller built-in 2.4G ELRS V3.0 and OPENVTX
- VTX Power up to 400mw
- ELRS V3.0 (Default), could flash elrs firmware for the receiver by wifi
- EX1103 KV110000 motors
- CaddxFPV Ant FPV camera
- Smooth and powerful
- Compatible for 2S Lipo/LIHV battery
- Recommend batteries: 2S 450mah/550mah/650mah battery (not included)
SPECIFICATIONS
Motors
- Mode: EX1103 KV11000
- Configuration: 9N12P
- Stator Diameter: 11mm
- Stator Length: 3mm
- Shaft Diameter: Φ1.5mm
- Motor Dimension(Dia.*Len): Φ13.5mm*15.5mm
- Weight(g): 3.8g
- No. of Cells(Lipo): 1-2S
Propellers
- Weight: 0.88g
- Material: PC
- Pitch: 2.3inch
- Props Diameter: 52.17mm
- Center Thickness: 5mm
- Center Hole Diameter: 1.5mm
FC
- MCU: STM32G473CEU6
- Gyro: ICM42688P
- Blackbox memory: 16MB
- Sensor: Voltage & Current
- BEC: 5V, Max. 2A
- UART: UART 1, UART 2, UART 3 (For RX), UART 4(For VTX)
- BetaFlight OSD: AT7456ELAH
- Camera plug: 0.8mm 3pin
- ESC: 12A continuous
- OPENVTX: 5.8GHz 48 channels, Max. 400mW
- FC firmware target: CRAZYBEEG473
- USB port: SH1.0-4Pin
- Battery connector: XT30 or A30
- Mounting hole size: 5mm x 25.5mm
- Weight: 83g without power pigtail and VTX antenna
ESC
- Power input: 1-2S Lipo input
- Current: 12A continuous, 15A peak
- ESC firmware: V0.19 48KHz Bluejay
- Firmware target: Z_H_30_48KHz
- Digital signal protocol: DShot300, DShot600
VTX
- OPENVTX Firmware
- Support firmware upgrade by openvtx configurator
- Output power: PIT/10/25/100/400
- Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz
- Channel SEL: SmartAudio2.1
- Modulation type: FM
- Operating temperature: -10℃~+80℃
- Antenna port: IPEX1/U.FL
RECEIVER
- Serial ExpressLRS 2.4GHz
- Antenna: Enameled copper wire 31mm length
- Firmware target: HappyModel EP1/EP2 2.4GHz RX
- Telemetry output Power: <12dBm
- Compatible with ExpressLRS V3.x.x TX Module
- ExpressLRS firmware version 3.0.1
- Support flash firmware by WIFI
- Bind method is the same like all ExpressLRS 2.4GHz receivers
Caddx ANT 1200TVL Camera
- Image Sensor: 1/3″ CMOS Sensor
- Horizontal Resolution: 1200 TVL
- TV System: NTSC or PAL
- IMAGE: 16:9 or 4:3
- Synchronization: Internal
- Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
- S/N Ratio : >52dB (AGC OFF)
- Video Output: CVBS
- Lens: 1.8mm
- Min. Illumination: 0.001Lux@F1.2
- Auto Gain Control: YES
- WDR: Global WDR
- DNR: 3D DNR
- Dimensions: 14*14mm(with bracket to 19*19mm)
- Wide Power Input: DC 3.7-18V
- Weight: 2g (N.W.)
DOWNLOADS
PACKAGE CONTENTS
- 1 x Happymodel Mobula8 1-2S 85mm Analog Micro FPV Whoop Drone
- 1 x Gemfan Hurricane 2023 tri-blade propellers (4CW+4CCW)
- 1 x Screw Driver
- 1 x Extra camera canopy
- Receiver Type:
- ExpressLRS
