Matek H743-Slim V4 + TBS Lucid 60A 8S Combo

A combo built for serious pilots. The Matek H743-Slim V4 packs the speed of an H7 processor, advanced filtering, and extensive I/O in a slim footprint—fully compatible with Betaflight, iNav, and Ardupilot for maximum flexibility. The TBS Lucid 60A 8S ESC, running AM32, delivers clean power through an 8-layer board with massive onboard capacitance and superior thermal dissipation, ensuring stability even under extreme loads. Together, they offer precise control, efficient power delivery, and the headroom needed for modern racing and freestyle builds.

Note: The Matek FC wiring ships with its ESC plug unpinned. It will need to be pinned but is a direct plug (no crossing wires)!

FC SPECIFICATIONS

• MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash
• IMU: Dual ICM42688P
• Baro: DPS368
• OSD: AT7456E (SPI2)
• Blackbox: MicroSD card socket
• 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
• Dimensions: 36 x 36 x 5 mm (FC)
• 13x PWM outputs(including “LED” pad)
• 2x I2C
• 1x CAN
• 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2)
• 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
• 1x SPI3 breakout
• USB Type-C(USB2.0)
• 1x JST-SH1.0_8pin connector (Vbat/G/Curr/Rx8/S1/S2/S3/S4)
• 1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G)

• Dual Camera Inputs switch
• 5V 0r Vbat(2A) filtered power ON/OFF switch

• DJI FPV OSD is supported by any spare UART

• Power

  • Vbat Input: 6~36V (2~8S LiPo) with TVS protection
  • BEC: 5V 2.5A cont. (Max.3A)
  • LDO 3.3V: Max.200mA
  • VBat filtered output 2A for VTx and camera
  • No Current Sensor built-in
  • ADC Vbat2 pad supports Max. 69V (voltage divider: 1K:20K)
  • Static power: 200mA@5V with Betaflight,  150mA@5V with ArduPilot

  FC Firmware

  • ArduPilot: MATEKH743
  • BetaFlight: MATEKH743
  • INAV: MATEKH743

ESC SPECIFICATIONS

• ESC software: AlkaMotors32 (AM32)
• ESC target: tbslu8s4in1
• Rated current: 55A x 4, 60 seconds
• Peak Current: 85A x 4, 10 seconds
• Propellers: Up to 11", over 7" requires good airflow
• Input: 3-8S Lipo
• Protocol: Bi-directional Dshot 300/600), KISS ESC Telemetry
• ESC current port: Yes
• BEC: No
• Size: 50mm*42mm
• Mounting: Gorilla-mount (39.5 x 16.0mm) & 30.5x30.5 mm or brackets for 20x20 mm,
• Weight: 17.58g, 22g incl. brackets

Physical

• Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
• Weight: 24.5g (combo of FC & ESC)

Package Contents

• 1x H743-SLIM-V4
• 6x Silicon grommets M4 to M3
• 1x JST-SH1.0_8pin cable, 5cm
• 2x JST-SH1.0_8pin connectors
• 1x JST-GH-4P to JST-GH-4P cable for CAN port, 20cm
• TBS Lucid 8S 4in1 ESC
• 4x 2.2x4mm standoffs
• Aluminum top bracket for 20x20 FCs
• XT60 power connector
• 560uF 8S Capacitor 
• 4x M2x12 screws
• 4x M2x14 screws (for 30x30 mount)