Happymodel Mobula7 O4 2S ELRS Whoop - XT30
*May differ from pictures shown.
The Happymodel Mobula7 O4 micro FPV whoop comes out now . It comes with the new DJI O4 air unit which would provide excellent and unbelievable FPV footage. And the new Happymodel RS1102 KV10000 motor with HQPROP 45mm propellers , bring a powerful and smooth flying experience. This would be a good option for indoor and backyard FPV flying.
Features
- Equipment with New DJI O4 air unit
- 2S battery support Powerful and Smooth freestyle flying
- UART ExpressLRS receiver support stable control link
- Lighter and small for indoor FPV
Specifications
Motor
- Mode: RS1102 KV10000
- Configu-ration:9N12P
- Stator Diamter:11mm
- Stator Length:2mm
- Shaft Diameter:Φ1.5mm
- Motor Dimension(Dia.*Len):Φ13.5mm*14mm
- Weight(g):2.8g
- No.of Cells(Lipo):1-2S
Propellers:
- Weight:0.25g
- Material: Poly Carbonate
- Pitch:0.9
- Props Dia:45mm
- Hub Thickness:5mm
- Shaft:1.5mm
Flight controller:
- MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
- GYRO Sensor: BMI270 (SPI connection)
- Mount hole size: 25.5mm*25.5mm
- Power supply: 1-2S battery input (DC 2.9V-8.7V)
- Built-in 12A(each) Blheli_S 4in1 ESC
- Built-in Serial ExpressLRS 2.4G
- Built-in BMP280 Barometer
- Built-in 8MBp blackbox
- Built-in voltage meter sensor , voltage meter scale 110
- Built-in current meter sensor , current meter scale 470
Onboard 4in1 ESC:
- Power supply: 1-2S LiPo/LiPo HV
- Current: 12A continuous peak 15A (3 seconds)
- Support BLHeli_S Bluejay firmware
- Factory firmware: Bluejay ESC V0.19
- Firmware target: Z-H-30
- Default protocol: DSHOT300
- When use 1s battery and high KV 0702/0802 motors, should set startup power to 1100/1200
Onboard UART ExpressLRS 2.4GHz Receiver:
- Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
- RF Frequency: 2.4GHz
- Antenna: enameled copper wire 31mm length
- Telemetry output Power: <12dBm
- Default firmware version: ExpressLRS V3.0.1
- Firmware target: HappyModel EP 2400 RX
- Could update firmware via ExpressLRS configurator
DJI O4 Air Unit:
- Weight:
Air Unit (camera module included): Approx. 8.2 g - Transmission Module: 30×30×6 mm (L×W×H)
- Camera Module: 13.44×12.36×16.50 mm (L×W×H)
- Camera Cable Length: 50mm
- Coaxial Cable: 50 mm
- 3-in-1 Cable: 50 mm
- Operating Frequency:
5.170-5.250 GHz
5.725-5.850 GHz - Operating frequency varies by region. Refer to local regulations.
Transmitter Power (EIRP):
5.1 GHz: <23 dBm (CE)
5.8 GHz:
<30 dBm (FCC)
<14 dBm (CE)
<30 dBm (SRRC) - Live View Quality: 1080p at 30/50/60/100fps
***If you want to use DJI FPV Remote controller, please change betaflight settings like following picture,no need do any hardware modification to the flight controller:
Package Contents
- 1 x Happymodel M80 Frame
- 1 x CrazyF405HD ELRS flight controller firmware target:BETAFLIGHTF4
- 4 x RS1102 KV10000 brushless motor
- 1 x HQPROP 45MMX2 bi-blade propellers(4cw+4ccw)
- 1 x DJI O4 Air unit
- 1 x Canopy
- 1 x Screw driver
- Receiver Type:
- ExpressLRS