HappyModel Bassline 2 Inch Analog ELRS 2.4 - 2S BNF

Introduce the Bassline , inspired from Our team pilot Nathan Loopz
This idea was originally born in 2019, and today we make it into a BNF. Even though we have many excellent Micro Freestyle drones now days, the Bassline’s performance is still the craziest.

FEATURES

• X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and OPENVTX
• VTX Power up to 400mw
• Support ELRS V3.0 (Need to upgrade firmware)
• Powerful EX1103 KV11000 motors
• CaddxFPV Ant FPV camera
• Recommend 2S 350mah/450mah/550mah/650mah battery (Not include)
• Battery tray size: Maximum support for batteries with a width of approximately 17mm and a height of approximately 13mm

FC SPECIFICATIONS

• X12 ELRS V2.1 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
• X12 Frsky V2.1 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
• X12 Flysky V1.0 flight controller built-in SPI Flysky 2.4G receiver Target: CRAZYBEEF4FS
• X12 PNP V1.1 flight controller without onboard receiver Target: CRAZYBEEF4DX
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: ICM20689 or ICM42688P(SPI connection)
• Mount hole size: 25.5mm*25.5mm
• Power supply: 1-2S battery input (DC 2.9V-8.7V)
• Built-in 12A(each) Blheli_S 4in1 ESC
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G OpenVTX 0mw~400mw
• Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
• Built-in voltage detection
• Built-in current sensor

4-IN-1 ESC SPECIFICATIONS

• Power supply: 1-2S LiPo/LiPo HV
• Current: 12A continuous peak 15A (3 seconds)
• Support BLHeliSuite programmable
• Default Factory firmware: Z_H_30_REV16_7.HEX
• Default protocol: DSHOT300
• Support Bluejay firmware

ELRS SPI RECEIVER SPECIFICATIONS

•  2.4GHz Receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz
• ExpressLRS Firmware version: V2.0
• RF Frequency: 2.4GHz
• Antenna : SMD antenna
• Telemetry output Power: <12dBm
• Receiver protocol: SPI ExpressLRS
• Compatible with ExpressLRS V2.0 TX Module
• Couldn’t flash separately ExpressLRS firmware
• Could flash FC firmware to support ExpressLRS v3.0 TX module

MOTOR SPECIFICATIONS

• Mode: EX1103 KV11000
• Configu-ration:9N12P
• Stator Diamter:11mm
• Stator Length:3mm
• Shaft Diameter:Φ1.5mm
• Motor Dimension(Dia.*Len):Φ13.5mm*15.5mm
• Weight(g):3.8g
• No.of Cells(Lipo):1-2S

PROPELLER SPECIFICATIONS

• Weight:0.88g
• Material: PC
• Pitch:2.3inch
• Props Dia:52.17mm
• Center Thickness:5mm
• Center Hole Dia:1.5mm

CADDX ANT 1200TVL CAMERA SPECIFICATIONS

• Image Sensor: 1/3″ CMOS Sensor
• Horizontal Resolution: 1200 TVL
• TV System: NTSC or PAL
• IMAGE: 16:9 or 4:3
• Synchronization: Internal
• Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
• S/N Ratio : >52dB (AGC OFF)
• Video Output: CVBS
• Lens: 1.8mm
• Min. Illumination: 0.001Lux@F1.2
• Auto Gain Control: YES
• WDR: Global WDR
• DNR: 3D DNR
• Dimensions: 14*14mm(with bracket to 19*19mm)
• Wide Power Input: DC 3.7-18V
• Weight: 2g (N.W.)

ONBOARD 5.8GHZ OPENVTX SPECIFICATIONS

• Firmware version: OPENVTX
• Smartaudio v2.1
• PIT Mode support
• RCE Mode support
• Channels:48ch
• Transmitting Power: 0/RCE/25mw/100mw/400mw
• Power supply: DC 5V
• Current (5v): <650ma (400mw)

PACKAGE contents

• 1 x Happymodel Baseline 2S 2" Brushless Analog FPV Racing Drone